[Linux-bruxelles] Intel Corp. PRO/Wireless LAN 2100 3B Mini PCI Adapter
Luc Viatour
l.viatour at mm.be
Jeu 23 Sep 15:37:14 CEST 2004
Le jeu 23/09/2004 à 13:41, Luc Viatour a écrit :
> Merci à vous cela fonctionne :-)
Je me suis réjoui un rien trop vite!
En fait c'est iwconfig qui découvre la carte mais ifconfig????
Détails:
Pour ifconfig j'ai ceci:
=============================================================
xdaopen:/home/xd# ifconfig
eth0 Lien encap:Ethernet HWaddr 00:0A:E4:21:84:C8
inet adr:192.168.10.125 Bcast:192.168.10.255
Masque:255.255.255.0
adr inet6: fe80::20a:e4ff:fe21:84c8/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1267818 errors:0 dropped:0 overruns:0 frame:0
TX packets:84726 errors:2 dropped:0 overruns:0 carrier:2
collisions:2975 lg file transmission:1000
RX bytes:425668287 (405.9 MiB) TX bytes:9519428 (9.0 MiB)
Interruption:10
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:159823 errors:0 dropped:0 overruns:0 frame:0
TX packets:159823 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:39057008 (37.2 MiB) TX bytes:39057008 (37.2 MiB)
=====================================================================
Pour iwconfig j'ai ceci:
======================================================================
xdaopen:/home/xd# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11b ESSID:"" Nickname:"ipw2100"
Mode:Managed Channel:0 Access Point: 00:00:00:00:00:00
Bit Rate=0kb/s Tx-Power=32 dBm
Retry:on RTS thr=2304 B Fragment thr:off
Encryption key:off
Power Management:off
eth2 no wireless extensions.
sit0 no wireless extensions.
=========================================================================
si je fais un ifup eth1 j'ai ceci:
xdaopen:/home/xd# ifup eth1
Ignoring unknown interface eth1=eth1.
xdaopen:/home/xd#
----------------
Pourtant un lspci donne:
0000:02:06.0 Network controller: Intel Corp. PRO/Wireless LAN 2100 3B
Mini PCI Adapter (rev 04)
----------------
Pour info j'ai aussi installé ifplugd qui devrait normalement activer et
détecter automatiquement l'interface qui a trouvé du réseau (je sais pas
si cela fonctionne).
Ma question est la suivante: Pourquoi un ifup eth1 ne fonctionne pas?
J'ai oublié quelque-chose?
--
Luc Viatour - Dupedi S.A.
rue de Stalle - 70-82 - 1180 Bruxelles
Tél: 32.2.333.07.18 - Fax: 32.2.332 05 98 - Web-site: www.mm.be
Plus d'informations sur la liste de diffusion Linux-bruxelles